Company News
CURRENT:HOME > NEWS > Company News
What should be paid attention to when the surface treatment of mobile phone shell is processed by reciprocating automatic sandblasting machine?
[2026-11-04]

What should be paid attention to when the surface treatment of mobile phone shell is processed by reciprocating automatic sandblasting machine?


The material of mobile phone shell is mostly aluminum alloy, stainless steel, plastic, titanium alloy, etc., which requires strict appearance consistency, dimensional accuracy and surface roughness. The reciprocating automatic sandblasting machine can realize stable sandblasting in batches by means of uniform reciprocating movement of the spray gun and the cooperation of workpiece positioning tools. It is a common equipment for matte, wiredrawing texture, deburring and pre-treatment sanding of mobile phone shell. However, if any link of sand blasting parameters, fixtures, abrasive selection, equipment debugging and process control is not properly controlled, there will be problems such as color difference, sand marks, deformation, dirt, low yield and so on. In mass production, it is necessary to implement the control points from early commissioning, production control, equipment maintenance and safety protection.

First of all, it is necessary to distinguish materials and control abrasive selection. There are great differences in the types and particle sizes of abrasives suitable for mobile phone housings made of different materials. White corundum and glass beads are commonly used for aluminum alloy housings, which can make a delicate and soft matte effect. Brown corundum can be used for stainless steel shell to improve adhesion; The plastic shell should use abrasive with low hardness to prevent breakdown and erosion of the substrate. Abrasive particle size directly determines the thickness and feel of the sand surface. The same batch of production must ensure the uniformity of abrasive grades and avoid mixing. During the production process, the abrasive state is continuously monitored, and when there is too much broken fine powder and dust, it is timely screened and replenished. Too much powder will cause surface fogging and uneven color difference, and when coarse particles are mixed, it is easy to produce obvious deep sand marks, which directly leads to poor appearance. At the same time, it is necessary to control the oil content and impurity content of the abrasive to prevent oily impurities from adhering to the surface of the shell, which will affect the bonding force of subsequent anodizing, spraying and coating.

Secondly, the parameters of reciprocating mechanism and spray gun are debugged and solidified. The reciprocating sandblasting machine relies on the cross beam to drive the spray gun to do uniform reciprocating motion, and the walking speed, stroke range, spray gun angle, gun distance and injection pressure of the spray gun are the core parameters. The gun distance is too large, the sandblasting strength is insufficient, and the sand surface is bright; The gun distance is too small and the impact force is concentrated, which is easy to cause local overspray and concave deformation of the shell. The inclination angle of the spray gun needs to be unified, and a reasonable injection angle is generally maintained. It is forbidden to spray vertically at a fixed point for a long time. Fixed-point impact can easily cause deformation of the thin edge and thin wall of the shell. The reciprocating speed should match the conveying rhythm. If the speed is too fast, the sand grain is shallow, and if the speed is too slow, the productivity will decrease and it will be easy to overspray. When multiple guns are arranged, the pressure and flow rate of each spray gun are consistent to prevent the sand surface in the left and right areas from being different in depth. After the parameter debugging is completed, the records shall be locked, and the batch and model shall not be changed at will, and the appearance must be confirmed by re-proofing before changing the model.

Fixture positioning and workpiece clamping are the key links to ensure consistency. The shape of mobile phone shell is complex, with camera hole, side key slot and thin-walled middle frame. The tooling needs to be accurately positioned to ensure the uniform placement position of each workpiece and avoid local spray leakage or overspray caused by offset. Soft wear-resistant materials are selected at the supporting position where the tooling contacts the shell to prevent the appearance surface from being pinched and crushed; For the areas that need to be protected, such as the conductive position, the assembly sealing groove and the lens step, a high-temperature and wear-resistant shielding fixture should be made in advance, and the shielding film should be tightly attached, so that sand can not be tilted and leaked during sandblasting. The clamping force is moderate, and the aluminum alloy middle frame thin-walled parts are easy to be plastically deformed when clamped too tightly, and become warped after sandblasting. Check the wear of tooling before each batch of production, and replace the locating pin and supporting block in time after wear to prevent the batch from being misaligned.

The environment, dust recovery and workpiece cleaning control in the production process can not be ignored. There is a large amount of dust in the sand blasting operation, so the dust removal and recovery system of the equipment must be kept in normal operation. The dust concentration in the cabin is too high, and the suspended sand particles repeatedly hit the workpiece, which will cause the sand surface to be hazy and gray, which will affect the texture. Keep the equipment cabin sealed to reduce dust spillage and pollution to the workshop. After the sandblasting of the workpiece is completed, a purging station shall be set up, and dry and clean compressed air shall be used to blow out the residual abrasive in the gaps and grooves of the cavity. If the residual abrasive is brought into the next anode or spraying process, it will cause bad particles and needle points. The compressed air source must be equipped with a drying and filtering device, and the oil-water separation is in place. The air flow with oil and water will agglomerate the sand and form spots on the surface of the shell, which will directly lead to batch scrapping. The temperature and humidity in the workshop remain stable. If the humidity is too high, the abrasive will easily absorb moisture and agglomerate, blocking the spray gun nozzle.

We should also pay attention to the protection and size control of the workpiece itself. The mobile phone shell has a thin wall thickness, especially the aluminum alloy middle frame, which has limited impact resistance. High-pressure sandblasting is easy to cause corner collapse and hole deformation. For thin-walled areas, the injection pressure can be appropriately reduced and the number of single sandblasting coverage can be reduced. After sandblasting, the roughness, appearance and outline size shall be randomly checked, and compared with the standard sample. Once the sand grain becomes coarse, color difference and deformation are found, the machine shall be stopped immediately for investigation. Different types of shells are produced separately. When the machine is changed, the residual abrasive in the silo, pipeline and spray gun is thoroughly cleaned to prevent mixing.

Finally, do a good job in equipment maintenance and operation safety management. The guide rail, synchronous belt and screw rod of reciprocating transmission mechanism are lubricated regularly to prevent the reciprocating walking from being stuck and the speed is fast and slow, resulting in uneven sand marks; Nozzle and bushing are vulnerable parts, and the flow rate is unstable after wear, so it is necessary to check and replace them regularly. Operators should wear dust-proof protective articles, the equipment should be grounded reliably, and dust explosion-proof management should be done well.

Although reciprocating automatic sandblasting has a high degree of automation, the mobile phone shell is a high-precision appearance piece, which requires extremely high stability. Only by standardizing abrasive management, curing sand blasting process parameters, doing a good job of tooling shielding, continuously monitoring dust removal and purging effect, and regularly maintaining reciprocating transmission and spray gun components can products with uniform appearance and qualified size be stably produced, and the yield of subsequent surface treatment processes can be guaranteed to be stable.


【RETURN】